Відео

It MIGHT actually be a drone issue. However, remove the 'controller' battery and leave it disconnected for 5 minutes. If that fails go to www.3drpilots.com for far more in depth trouble shooting. Good luck

Which GoPro Model? if it's any other model than a GP4 BLACK you'll need to install the requisite 'counter weights' on the gimbal.. Otherwise, It sounds like it may be a bad gimbal. Just make sure that under no circumstances that the gimbals flywheel, it has to spin freely, is not contacting anything. Especially the circuit board that it very closely reside to.. Introducing drag, of any kind, to the flywheel is a very bad thing.. The cable routing must be closely looked at while closing up the drone. The last part of the video where I pull the cable to one side is important. It keeps the cable from contacting the flywheel.. Hope that helps...

At 4:55 - That's the flywheel.. It's very easy for the gimbal power cable, shown right next to the damper/flywheel, to contact and impede its rotation.. This must be completely avoided for proper gimbal operation. Hence the final routing of this cable when closing it all up.

Firmware ?'s - go to; 3drpilots.com This is the best resource for SOLO pilots...

It's designed to be removable with NO tools.. Many people have damaged the GPS Cover in the process. If done properly with either method you should have no problem or damage. Cheers

Cascade Graphics - I haven't had much luck in trying to remove it by squeezing. Once I discovered that the tabs that hold it in are actually on the on top, I can remove it much easier and with no need to force anything. The screwdriver that comes included with the gimbal is the perfect size to release the tabs. If you're reasonably gentle with it, there is little risk of damaging anything.

It was not pre intstalled I just bought the package deal at best buy so it came with it and I installed it myself. I updated the firmware right out of the box as they suggest so I believe I have the latest software/firmware. Its a solo, and currently the system info is --- gimbal = 1.3.4, controller = 2.1.0, controller firmware = 1.2.8 thanks for taking the time to help

go pro is hero 4 silver and the version the gopro is running shows 3.0.2, the firmware of the 3dr solo is as follows app -- 2.1.0 gimbal -- 1.3.4 controller -- 2.1.0 controller firmware 1.2.8 thanks for the help!

Mitch Ghelfi did you ever get your gimbal to work. did your controller ever detect it. I am in the same boat. Gimbal has green breathing light, and also stabilizes if touched, but remote says no gimbal detected. any help would be appreciated .has all the latest updates

Which GoPro? Stock gimbal accommodates GP4 BLACK.. All other GP4 (i.e. Silver) require counter weights to be installed. Also, on the interior of the GIMBAL BAY the cable assembly can accidentally come in contact with rotational flywheel (silver in color) creating drag on the gimbal and or the flywheel may come in contact with surrounding circuit board (see video at minute 4:09). Any drag on the flywheel induces a load onto the gimbal motor creating all sorts of issues... Good luck

Check the 5 minute mark for the recommended routing of the cable.

+Larry Marshall Yes, they are available at stores.ebay.com/voodoocrewdesigns/ Thanks for your interest, we really appreciate it...

Cascade Graphics

Yes - just re-listed them.. Much thanx. stores.ebay.com/voodoocrewdesigns/

+Robbie Mazzoni stores.ebay.com/voodoocrewdesigns/ Store manager was on vacation. Most items are now resisted... Thanks for your interest, we really appreciate it..

+Brian Lytle I believe mine was 3/8 thick.. 1/4" will do..

Where can I buy that rubber foam ???

1/4 inch thick

Any hardware store - Lowes - Home Depot etc...

Thanks

+david ringler No, disconnecting the GPS's molex connector is the same as powering the Solo off. Meaning it's a passive action, as are most GPS antennas, including WAAS GPS.

+oscar gomez I Just re-listed the 'Drone Boost' card on eBay.. use this link stores.ebay.com/voodoocrewdesigns to access the store.. Thanks

You don't sell the boost anymore?

+xyreyes The Foam I used had an adhesive backer. So no it won't move. I placed one piece on each gimbal rubber isolator (2) and one piece on the interior forward section, on the chassis, where the HDMI cable magnet rested directly on the SOLO's plastic frame. And finally one last piece above the gimal data cable, just in case it were to pick up any vibrations from the battery tray/chassis contact. It's temping to go over board with the foam rubber but i just focused on the points where the HDMI cable was floating and touching the gimbal or the housing.. If there is only one thing to take away from all of this is that the 'silver gimbal rotation damper' cannot be allowed to have anything, including the main board, come in contact with it, ever. Any resistance or undue load is the primary culprit of gimbal failure.. Hope that helps.. Cheers and thank for watching.

+Cascade Graphics Appreciate the quick reply. I completed the mod now and will fly my drone soon. I'll let you know the results. Might even upload the video. Thanks again

+xyreyes Didn't end up working for me but thank you anyways.